Our Products

With Bondtech’s INDX system arriving on the Prusa CORE One, multi-nozzle printing is quickly becoming the new standard in 3D printing workflows. However, as the number of colors increases, so does the complexity—more spools, more clutter, and less workspace efficiency.

That’s where INBXX comes in.

INBXX is a fully configurable filament management system designed to bring order, efficiency, and elegance to your printing setup. More than just a spool holder, it is a complete cabinet solution engineered to optimize your workspace while keeping your materials in perfect condition.

It features an enclosed environment to protect filament from dust and humidity, with support for active heating and drying to ensure consistent print quality.

Whether you are using a classic MMU3 setup or scaling up to a 10-spool INDX configuration, INBXX adapts seamlessly to your needs.

Link: Voxel 3D and Introduction video

The MOG Kit is an extraordinary fully 3D-printed tribute to the legendary Unimog U5023, bringing one of the world's most iconic off-road trucks into the hands of makers, RC enthusiasts, and scale model builders.

Featuring functional portal axles, a realistic drivetrain, and authentic scale details, the MOG delivers an engaging build experience and impressive performance on challenging terrain. Optimized for desktop 3D printers, the kit combines engineering, craftsmanship, and customization into one rewarding project.

This project contains more than 582 3D printed parts collected in 101 plates ready with the correct orientation!

A minimum 180x180 print bed is required.

Link: Official website, Build guide, Assembly video.

The Unicorn Chasing Kit is a resonance compensation toolkit centred around two core components: the Rethonance Nozzle, a V6-compatible nozzle with a built-in ADXL345 accelerometer and the Rethonance Hub, a magnetic, bed-mountable board that consolidates connectivity for ADXL sensors, motor thermistors, and a GPIO extension port — all over a single USB connection. Together, they provide a convenient way for users to precisely measure resonance at where it actually matters - the nozzle.

Link: LDO Docs and Github

The CPS 3 is a simple to build, yet very capable submarine kit designed by CPSdrone team! It includes every single component required to build the drone.

Buy CPS3 kit from the official store and learn the course.

More videos can be found on CPSdrone Youtube channel.

The new Orbiter v3.5 is based on the well-known Orbiter v3.0, with several refinements that further enhance its extrusion performance.

Link: Official Website

Elevate your Voron 2.4 or Trident to the next level with the LDO Monolith CNC Gantry Kit.

Link: Github

United States: West3D; Fabreeko; KB-3D

Canada: 3D Lab Tech

Australia: Dremc

United Kingdom:123-3D; onetwo3D

Germany: 3DPartner

France: MyRigs

Hungary: Zen3D Laboratories

Russia: RRF3D

India: DConqueror3D

Nitehawk-SB v2 by LDO is a toolboard specifically designed for the Voron Stealthburner toolhead. It is a toolhead PCB featuring STM32G0B1 MCU, TMC2209 stepper drive, ADXL345 accelerometer, USB HUB all integrated into one board. Nitehawk v2 retains the same form factor of the original Nitehawk-SB but much of the circuitry and layout has been completely redesigned from the ground up. 

Nitehawk uses USB communication with the RPI rather than CAN. So the software and hardware setup is far simpler and familiar to most people who have setup Klipper printers before.

Link: LDO Docs and Github

This extrusion blind joint seal is designed by LDO to be used inside 2020 aluminum extrusions. It helps prevent gases from escaping during printing and also reduces outside air from entering, creating a more stable printing environment.

The installation method is the same as a T-nut: insert one side first, then press the other side in. Finally, slide it along the extrusion slot until it reaches the end. Please refer to the illustration for guidance.

What if the Voron Design team decided to stop making 3D printers and build a PC case instead? 
Spoiler: they didn’t. This is not an official Voron project… but it might be what it would look like if they did. VoronPC is a fully 3D-printed, extrusion-framed computer case inspired by the clean, modular, and open-source ethos of Voron printers. Designed to house a full custom streaming workstation, it blends maker aesthetics with real-world PC hardware needs.

The Case can fit a 199mm tall Air Cooler Tower and a 400mm long GPU (approximately). Standard ATX power Supply fits in the basement. Files include mounting for 140mm & 60mm exhaust fans, as well as 3x 120mm top mounted fans. Blank acrylic panel DXFs are included for adding additional fans to or using as windows.

--MandicReally

More information can be found on Printables and Youtube.

The LCP300-24D5 is a compact, fully enclosed 300W dual-output power supply for 3D printing applications. Featuring power factor correction and gallium nitride technology, the LCP300-24D5 provides 24V and 5V outputs with an efficiency of over 90%.

Documentation:

LDO Docs

Github

It is a high-performance, coreXY 3D printer designed for precision, speed, and reliability, ideal for enthusiasts and professionals alike With its fully enclosed design and modular construction, it delivers excellent temperature stability and supports a wide range of materials.

Link: Github and LDO wiring guide